References of "Kordoš, P"
     in
Bookmark and Share    
Full Text
Peer Reviewed
See detailLow Current Dispersion and Low Bias-stress Degradation of Unpassivated GaN/AlGaN/GaN/SiC HEMTs
Bernát, J.; Pierobon, R.; Marso, Michel UL et al

in Physica Status Solidi C. Current Topics in Solid State Physics (2005), 2(7), 2676-2679

The performance of unpassivated GaN/AlGaN/GaN/SiC HEMTs with intentionally undoped and doped barrier structures are extensively studied. No drain current dispersion between DC and 50 ns pulses on doped ... [more ▼]

The performance of unpassivated GaN/AlGaN/GaN/SiC HEMTs with intentionally undoped and doped barrier structures are extensively studied. No drain current dispersion between DC and 50 ns pulses on doped devices and less than 10% dispersion on undoped ones is observed. The full (100%) current recovery on undoped sample was measured in 1μs. The drain current extrapolated from 2 GHz large signal measurements corresponds to the measured static drain current confirming negligible current dispersion of our devices. Insignificant (<5 %) degradation in overall device performance parameters (IDs, gm, fT, fmax, Pout) on both undoped and doped structures after 12-hour-long bias stress was obtained. These results documents that suitable device performances can be obtained also on unpassivated GaN-based HEMTs. [less ▲]

Detailed reference viewed: 64 (0 UL)
Full Text
Peer Reviewed
See detailHigh-power SiO2/AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors
Kordoš, P.; Heidelberger, G.; Bernát, J. et al

in Applied Physics Letters (2005), 87(14), 143501-143504

We report on SiO2 /AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors MOSHFETs , which exhibit a 6.7 W/mm power density at 7 GHz. Unpassivated and SiO2-passivated heterostructure ... [more ▼]

We report on SiO2 /AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors MOSHFETs , which exhibit a 6.7 W/mm power density at 7 GHz. Unpassivated and SiO2-passivated heterostructure field-effect transistors HFETs were also investigated for comparison. Deposited 12 nm thick SiO2 yielded an increase of the sheet carrier density from 7.6 .10^12 to 9.2 .10^12 cm−2 and a subsequent increase of the static drain saturation current from 0.75 to 1.09 A/mm. The small-signal rf characterization of the MOSHFETs showed an extrinsic current gain cutoff frequency fT of 24 GHz and a maximum frequency of oscillation fmax of 40 GHz. The output power of 6.7 W/mm of the MOSHFETs measured at 7 GHz is about two times larger than that of HFETs. The results obtained demonstrate the suitability of GaN-based MOSHFETs for high-power electronics. [less ▲]

Detailed reference viewed: 80 (0 UL)
Full Text
Peer Reviewed
See detailLarge-area traveling-wave photonic mixers for increased continuous terahertz power
Michael, E. A.; Vowinkel, B.; Schieder, R. et al

in Applied Physics Letters (2005), 86(11), 111120-111123

A large-aperture design for terahertz traveling-wave photomixers, continuously pumped free space by two detuned diode lasers, is proposed and experimentally verified for devices based on low-temperature ... [more ▼]

A large-aperture design for terahertz traveling-wave photomixers, continuously pumped free space by two detuned diode lasers, is proposed and experimentally verified for devices based on low-temperature-grown GaAs sLT-GaAsd. It combines the advantages of conventional interdigitated small-area structures and traveling-wave devices. An output power of 1 µW at the mixing frequency of 1 THz was measured in initial testing, which meets local oscillator power requirements for superconducting heterodyne mixer devices. [less ▲]

Detailed reference viewed: 65 (0 UL)
Full Text
Peer Reviewed
See detailUltrafast Low-Temperature-Grown Epitaxial GaAs Photodetectors Transferred on Flexible Plastic Substrates
Mikulics, M.; Adam, R.; Marso, Michel UL et al

in IEEE Photonics Technology Letters (2005), 17(8), 1725-1727

We demonstrate low-temperature (LT)-grown GaAs photodetectors transferred on flexible polyethylene terephthalate (PET) plastic substrates. The LT-GaAs layer was patterned into 20 20 m2 chips, which after ... [more ▼]

We demonstrate low-temperature (LT)-grown GaAs photodetectors transferred on flexible polyethylene terephthalate (PET) plastic substrates. The LT-GaAs layer was patterned into 20 20 m2 chips, which after placing on the PET substrates were integrated with coplanar strip transmission lines. The devices exhibit low dark currents ( 2 10 8 A), subpicosecond photoresponse time, and signal amplitudes up to 0.9 V at the bias voltage of 80 V and under laser beam excitation power of 8 mW at 810-nm wavelength. At the highest bias ( 80 V) level, an increase of the response time (up to 1.3 ps) was observed and attributed to the influence of heating effects due to low thermal conductivity of PET. Our LT-GaAs-on-PET photodetectors withstand hundredfold mechanical bending of the substrate and are intended for applications in hybrid optoelectronic circuits fabricated on noncrystalline substrates, in terahertz imaging, and in biology-related current-excitation tests. [less ▲]

Detailed reference viewed: 84 (0 UL)
Full Text
Peer Reviewed
See detailUltrafast Phenomena in Freestanding LT-GaAs Devices
Marso, Michel UL; Mikulics, M.; Adam, R. et al

in Acta Physica Polonica A (2005), VOL 107; PART 1

We report on the fabrication and high-frequency performance of our photodetectors and photomixers based on freestanding low-temperature-grown GaAs. The MBE-grown low-temperature GaAs layers are lifted ... [more ▼]

We report on the fabrication and high-frequency performance of our photodetectors and photomixers based on freestanding low-temperature-grown GaAs. The MBE-grown low-temperature GaAs layers are lifted from the native GaAs substrate and transferred on top of variety of host substrates. The freestanding devices exhibit breakdown electrical ¯elds above 200 kV/cm and dark currents below 3 £ 10¡7 A at 100 V bias. Device photoresponse shows 0.55 ps wide electrical transients with voltage amplitudes up to 1.3 V, measured using an electro-optical sampling technique with 100 fs wide laser pulses. Photomixing experiments at 460 GHz yield a 9 times higher output power for the freestanding device on Si/SiO2 host substrate compared to the native substrate. [less ▲]

Detailed reference viewed: 70 (0 UL)
Full Text
Peer Reviewed
See detailPhotomixers fabricated on nitrogen-ion-implanted GaAs
Mikulics, M.; Marso, Michel UL; Cámara Mayorga, I. et al

in Applied Physics Letters (2005), 87(4), 41106-1-3

We report on fabrication and measurement of photomixers based on nitrogen-ion-implanted GaAs. We used energies of 500 keV, 700 keV, and 880 keV to implant N+ ions into GaAs substrates with an ion ... [more ▼]

We report on fabrication and measurement of photomixers based on nitrogen-ion-implanted GaAs. We used energies of 500 keV, 700 keV, and 880 keV to implant N+ ions into GaAs substrates with an ion concentration of 3 1012 cm−2. The resulting material exhibited 110 fs carrier lifetime due to implantation-induced defects. Our photomixers were fabricated as metal-semiconductor-metal devices, placed at the feed point of a broadband antenna. Optoelectronic measurements were performed in the wavelength range between 350 nm and 950 nm. In comparison to their counterparts photomixers fabricated on low-temperature-grown GaAs the N+-implanted GaAs photomixers exhibit improvements on both the output power and responsivity. A maximal responsivity of above 100 mA/W was achieved and we did not observe any dependence of the mixer cut-off frequency on the bias voltage. These characteristics make N+-implanted GaAs the material of choice for efficient optoelectronic photomixers. [less ▲]

Detailed reference viewed: 72 (0 UL)
Full Text
Peer Reviewed
See detailInfluence of layer structure on performance of AlGaN/GaN High Electron Mobility Transistors before and after passivation
Bernát, J.; Javorka, P.; Fox, A. et al

in Journal of Electronic Materials (2004), 33((2004)), 436-439

Detailed reference viewed: 66 (1 UL)
See detailDC and Pulsed Behaviour of Undoped and Doped AlGaN/GaN/SiC HEMTs before and after Si3N4 passivation
Bernát, J.; Marso, Michel UL; Fox, A. et al

in Proc. 5th Intern. Conf. Advanced Semicon. Dev. & Microsystems ASDAM’04 (2004)

Detailed reference viewed: 27 (0 UL)
Full Text
Peer Reviewed
See detailPerformance of unpassivated AlGaN/GaN/SiC HEMTs after short-term electrical bias stress
Bernát, J.; Wolter, M.; Javorka, P. et al

in Solid-State Electronics (2004), 48((2004)), 1825-1828

Performance of unpassivated MOVPE grown AlGaN/GaN/SiC HEMTs under short-term electrical bias stress isreported. Insignificant degradation in DC and RF behaviour of prepared devices after 16 h stress at VD ... [more ▼]

Performance of unpassivated MOVPE grown AlGaN/GaN/SiC HEMTs under short-term electrical bias stress isreported. Insignificant degradation in DC and RF behaviour of prepared devices after 16 h stress at VD ¼ 21 V and VG ¼ 2:5 V is observed. This can be demonstrated by a maximum drain current of 1.03 and 1.01 A/mm and a peak extrinsic transconductance of 233 and 225 mS/mm before and after bias stress, respectively. Consecutive drain voltage sweeps indicates on low current collapse in samples investigated. The RF characteristics show a decrease of the fmax-tof T ratio from 2.23 to 2.15 and the saturated output power density measured at 2 GHz from 3.60 to 3.53 W/mm after the devices were stressed. This result indicates that reliable AlGaN/GaN/SiC HEMTs without passivation can be prepared. However, additional studies are needed to understand if the material structure and/or the device processing is responsible for low current collapse and RF dispersion in these devices. [less ▲]

Detailed reference viewed: 67 (0 UL)
Full Text
See detailInfluence of doping density on small and large signal characteristics of AlGaN/GaN/SiC HEMTs
Fox, A.; Marso, Michel UL; Bernát, J. et al

in Proc. 5th Intern. Conf. Advanced Semicon. Dev. & Microsystems ASDAM’04 (2004)

The small signal S-parameter and load pull measurements on AlGaN/GaN HEMTs with different doping densities are reported. The cut-off frequencies ft and fmax of 38 and 67 GHz respectively, and the maximal ... [more ▼]

The small signal S-parameter and load pull measurements on AlGaN/GaN HEMTs with different doping densities are reported. The cut-off frequencies ft and fmax of 38 and 67 GHz respectively, and the maximal output powers of 4.9 and 3.8 W/mm at 2 and 7 GHz respectively, were achieved. The parameter extraction from small signal S-parameters shows an increase of gate-source capacitance and transconductance with the doping concentration and hence its influence on small signal (ft and fmax) and power performance. [less ▲]

Detailed reference viewed: 53 (0 UL)
See detailGeneration of 1 THz radiation by photomixing in low-temperature-grown MBE GaAs
Mikulics, M.; Camara, I.; Marso, Michel UL et al

in Proc. 5th Intern. Conf. Advanced Semicon. Dev. & Microsystems ASDAM’04 (2004)

Detailed reference viewed: 57 (0 UL)
Full Text
See detailFabrication and performance of hybrid photoconductive devices based on freestanding LT-GaAs, Ultrafast Phenomena in Semiconductors and Nanostructure Materials VIII,
Adam, R.; Mikulics, M.; Wu, S. et al

in Proceedings of SPIE (2004), 5353 (2004)

We report on fabrication and high-frequency performance of our photodetectors and photomixers based on freestanding low-temperature-grown GaAs (LT-GaAs). In our experiments, the LT-GaAs/AlAs bilayers were ... [more ▼]

We report on fabrication and high-frequency performance of our photodetectors and photomixers based on freestanding low-temperature-grown GaAs (LT-GaAs). In our experiments, the LT-GaAs/AlAs bilayers were grown on 2-inch diameter, semi-insulating GaAs wafers by a molecular beam epitaxy. Next, the bilayer was patterned to form 10 × 10 μm2 to 150 × 150 μm2 structures using photolithography and ion beam etching. The AlAs layer was then selectively etched in diluted HF solution, and the LT-GaAs device was lifted from its substrate and transferred on top of a variety of substrates including Si, MgO/YBaCuO, Al2O3, and a plastic foil. Following the transfer, metallic coplanar transmission lines were fabricated on top of the LT-GaAs structure, forming a metal semiconductor-metal photodetectors or photomixer structures. Our freestanding devices exhibited above 200 V breakdown voltages and dark currents at 100 V below 3×10-7 A. Device photoresponse was measured using an electro-optic sampling technique with 100-fs-wide laser pulses at wavelengths of 810 nm and 405 nm as the excitation source. For 810-nm excitation, we measured 0.55 ps-wide electrical transients with voltage amplitudes of up to 1.3 V. The signal amplitude was a linear function of the applied voltage bias, as well as a linear function of the laser excitation power, below well-defined saturation thresholds. Output power from the freestanding photomixers was measured with two beam laser illumination experimental setup. Reported fabrication technique is suitable for the LT-GaAs integration with a range of semiconducting, superconducting, and organic materials for high-frequency hybrid optoelectronic applications. [less ▲]

Detailed reference viewed: 44 (0 UL)
Full Text
Peer Reviewed
See detailImpact of layer structure on performance of unpassivated AlGaN/GaN/SiC HEMTs,
Bernát, J.; Wolter, M.; Fox, A. et al

in Electronics Letters (2004), 40(1), 78-80

The performance of unpassivated AlGaN=GaN=SiC HEMTs prepared on different MOVPE grown layer structures is reported. An overall improvement of device characteristics using doped structures in comparison to ... [more ▼]

The performance of unpassivated AlGaN=GaN=SiC HEMTs prepared on different MOVPE grown layer structures is reported. An overall improvement of device characteristics using doped structures in comparison to undoped counterpart is observed. This can be demonstrated by IDS of 0.86 and 1.33 A=mm, gm of 220 and 273 mS=mm, fT of 33 and 43 GHz and fmax of 54 and 61 GHz for 0.3 mm gate length devices on undoped and doped structures, respectively. The DC=pulsed I–V characteristics as well as power measurements show insignificant RF dispersion of HEMTs on doped structures. These results underline the advantage of doped layer structures for preparation of high-performance AlGaN=GaN HEMTs. [less ▲]

Detailed reference viewed: 51 (0 UL)
Full Text
See detailLarge-area traveling-wave LT-GaAs photomixers for LO application
Michael, E. A.; Mikulics, M.; Marso, Michel UL et al

in SPIE - The International Society for Optical Engineering (2004), 5498 (2004)

Detailed reference viewed: 62 (0 UL)
Full Text
See detailAn optimization of terahertz local oscillators based on LT-GaAs technology
Mayorga, I. C.; Mikulics, M.; Schmitz, A. et al

in SPIE - The International Society for Optical Engineering (2004), 5498 (2004)

Detailed reference viewed: 52 (0 UL)
See detailNitrogen implanted GaAs for ultrafast photodetectors and photomixers
Mikulics, M.; Wolter, M. J.; Marso, Michel UL et al

in Proc. 5th Intern. Conf. Advanced Semicon. Dev. & Microsystems ASDAM’04 (2004)

Detailed reference viewed: 36 (0 UL)
Full Text
Peer Reviewed
See detailInfluence of a carrier supply layer on carrier density and drift mobility of AlGaN/GaN/SiC high-electron-mobility transistors
Marso, Michel UL; Bernát, J.; Javorka, P. et al

in Applied Physics Letters (2004), 84 (2004)

Sheet carrier concentration and low-field drift mobility of intentionally undoped and modulation-doped AlGaN/GaN heterostructures on SiC substrate were evaluated by capacitance-voltage and channel ... [more ▼]

Sheet carrier concentration and low-field drift mobility of intentionally undoped and modulation-doped AlGaN/GaN heterostructures on SiC substrate were evaluated by capacitance-voltage and channel conductivity measurements. Sheet carrier concentration and average mobility at 0 V gate bias correspond to standard Hall results. Sheet carrier density increases from 6.831012 cm22 for the undoped sample up to 131013 cm22 for the device with the highest doping concentration, while the mobility decreases from 1800 to 1620 cm2/V s. The local mobility, on the other hand, depends only on the actual sheet carrier density and is not influenced by the doping concentration of the carrier supply layer. It reaches a maximum value of 2100 cm2/Vs at a carrier density of 331012 cm22. [less ▲]

Detailed reference viewed: 83 (0 UL)
Full Text
Peer Reviewed
See detailA novel two-color photodetector based on an InAlAs-InGaAs HEMT layer structure
Marso, Michel UL; Wolter, M.; Kordoš, P.

in IEEE Photonics Technology Letters (2004), 16 (2004)(11), 2541-2543

The spectral responsivity of an InAlAs–InGaAs metal–semiconductor–metal diode above a two-dimensional electron gas (2DEG) is investigated as a function of the applied bias. At low voltages, only the ... [more ▼]

The spectral responsivity of an InAlAs–InGaAs metal–semiconductor–metal diode above a two-dimensional electron gas (2DEG) is investigated as a function of the applied bias. At low voltages, only the InAlAs layer above the 2DEG contributes to the photocurrent, while the InGaAs channel layer is activated at higher bias. This results in a voltage-dependent spectral response of the photodetector. The ratio of the responsivities at 1300 and 850 nm changes from 0.03- at 1-V to 0.44- at 1.6-V bias. This property makes the device a candidate suitable to detect and to separate optical information originated both from the GaAs (850 nm) and in the InGaAs (1300, 1550 nm)-based optoelectronic technology. [less ▲]

Detailed reference viewed: 71 (0 UL)
Full Text
See detailMSM varactor diodes based on AlGaN/GaN/SiC HEMT layer structures
Marso, Michel UL; Bernát, J.; Javorka, P. et al

in Proc. 5th Intern. Conf. Advanced Semicon. Dev. & Microsystems ASDAM’04 (2004)

The influence of a carrier supply layer on the electrical properties of MSM diodes based on AlGaN/GaN HEMT layer structures is investigated. The voltage dependence of the Schottky contact capacitance ... [more ▼]

The influence of a carrier supply layer on the electrical properties of MSM diodes based on AlGaN/GaN HEMT layer structures is investigated. The voltage dependence of the Schottky contact capacitance allows the use of the device as varactor diode with CMAX / CMIN ratios up to 17, tuneable by contact geometry. The carrier supply doping determines the sheet carrier density of the twodimensional electron gas channel, which is responsible for the transition voltage and the series resistance of the MSM diode. A device based on the highest doped layer structure shows a cutoff frequency as high as 65 GHz. [less ▲]

Detailed reference viewed: 75 (0 UL)
See detailVertical Double-Gate MOSFETs
Moers, J.; Trellenkamp, St; Marso, Michel UL et al

in Proc. 5th Intern. Conf. Advanced Semicon. Dev. & Microsystems ASDAM’04 (2004)

Detailed reference viewed: 55 (0 UL)